The Race Mower - Weekend 1 - Drag er outta the bushes.

    This mower was a project I had been meaning to get back to for almost 20 years. I purchased it when I was roughly 8-10 years old. I had accompanied my dad and my grandpa to look at a motor for my grandpas truck. The man selling the motor was selling out everything and there was this 1970s? Craftsman lawnmower, the perfect go kart for me.

    My dad and I worked on it for awhile at that time, but the project was eventually abandoned. It ended up outside in the bushes beside the garage, where it has sat for many years now. 

    Fast forward to 2023. One of my coworkers (knowing my interest in go-karts) asks if I happen to have a race mower. He informed me that there are a couple guys in the shop who have race mowers, and enter them in a yearly race. To nobody's real surprise: I did have a mower, and suddenly a reason to finish that project... Well maybe a little differently than my 10-year-old self had imagined.

    I drug the old mower out of the bushes and gave it a good wash off. The main body of the mower looked really good for its decade plus in the rain. The hood that was freshly sanded did not fare as well, but was still good and solid despite the new pitting. When we got it all cleaned off and took a look, it seemed the project was most of the way along when it was abandoned. 

    We had the whole thing apart when I was young, so it appeared we had gone pretty far in putting the mower back together. I stuck a battery in it just to see what would happen, and that was the real shocker. I hit the key and it turned over. It also sounded like it had compression. Now that I could see it might just run, it was time to get to work seeing if this neglected motor could run for us.

    We took the flywheel off and cleaned up the points. After a few attempts at cleaning: we had spark. All we needed now was fuel, and this motor would theoretically run. We mounted the hood and grill (as the hood holds the gas tank). We also cleaned out the gas tank, and ran a fresh line and filter. My dad took to cleaning and setting up the old carb. 

*Probably gonna leave the hood and grill rusty for that rat rod look.*

Would you believe the thing ran? It sure did. To my surprise: this old motor took little time to fire up, and with all the glorious roar to be expected of an old flathead with no exhaust.

^Tossed on some rusty moon caps from a scooter.^

    We still need a new carb, but we know she runs and that's a great starting point. Unfortunately the belt blew off when we tried to get it mowing... I mean, uh... Moving, so we are gonna have to wait to test out the transmission. There's only one good tire on the front right now anyways, so we may as well put together our new steering and front tires. That's got to wait until next week though.

C1500 Dually (The Unruly Dually) - Week 1

Once again I find myself knee deep in another questionable project... But lets rewind to the beginning.

About a year or so ago Alisha (my girlfriend) traded her 1987 Fiero for a 1988 C1500. The truck was originally a V6 truck, but someone had already swapped the motor and trans for running gear from an 89 1-ton. It was now wielding a 350 V8 and Turbo 400 trans. The truck was a bit of a rat rod, but mostly just ratty. The interior was complete garbage, to put it nicely. (We later picked up a full interior from a Silverado and have resurrected the interior.) The truck was no gem either, but was basically rust free, aside from the rear fender wells. Its flat black spray bombed paint job forever sealed its fate as a rat rod, but we were always searching for something to take it from ratty truck, to rat rod.

We had toyed with the idea of making it a dually, just for fun, when I had a dead 94 4x4 dually I couldn't get rid of. At the time it was no more than a funny idea, but it did spark an interest to look into it and if it would be doable. Not much information was out there, but i couldn't find anything yet to say it was impossible. A few months later my dually was sold, and I came across a 2wd dually being parted out. I instantly thought back to our crazy build plan, and couldn't resist the opportunity to actually try it. The truck had pretty tall gears (3.42) and with the tall first gear on the Turbo 400 trans, it really made for a slow doggy start. The 4.10 gears of the dually rear end would help make this thing get up and go like it should. The dually fenders fit the bill perfectly too, as the rear fender wells were rusted and needed work anyway. The swap idea seemed to fix two of our problems with the truck, as well as create something cool and unique that would take this poor little C1500 from Ratty to Rat Rod.

Here is the little C1500, Single cab, short box, as she sits right now.

Of course y'all know you wouldn't be seeing this post unless I went ahead and went for those c3500 dually parts... And here they are.

14 bolt full floater rear end with 4.10 gears

Fiberglass dually fenders

Got a great deal from Dakota at Black Pearl for all the dually parts;

- 14 Bolt 4.10 rear end

- Dually rims/whats left of tires

- Fiberglass dually fenders

- Front spindles with brakes

- Upper control arm

- 1 ton sway bar

and few other odds and ends from the same parts truck, including the cab lights.

As far as I have seen, this should be all I need to convert the C1500 to a dually. (Not that there is necessarily one way to do it). I will be keeping the 1500 suspension, as the truck wouldn't be legal to tow more anyways since it is still registered as a 1500. A lot of what we like about the dually swap idea is the better traction, so the softer 1500 suspension is going to work in our favor.

Tomorrow we will be starting prep work on and for the dually fenders.

Leaf Cargo Deck. Day#2

The next morning started with a search for my can of flat black paint. I added two supports on either side of the frame to support the top where it would overhang. and gave it a coat.

I decided I wanted to make the top as solid as possible and not have any opening compartments on the sides. I too out the jigsaw and created two holes in the main frame so the side compartment could be used to sore things.

And here it is! The rear framework is painted and fits perfectly into the car. I should also mention i put the rear section of carpet back in.

For the rear section I added a plywood bottom so that the part between the 4x4 posts could be used as a shallow storage compartment

I also added an amp onto the bottom portion that will hang under where the rear seat used to be. This will be used for when I upgrade my stereo... but that is another post. I just added this on now to make it easier on myself later.

And here is what it looks like with both sections in. The 4x4 posts are just simply screwed to the 2x6 I trimmed for the rear section. This holds it plenty good enough as it will get allot of its strength from the plywood top too.

Under the un-carpeted section will be my stereo amp and wiring.

While i was able to access it, I added two accessory batteries that will later be used for the stereo. the wires just hang in the un-carpeted area now, capped off until I used them.

I then cut the plywood for the middle section. I used on 1" strip in the middle that will keep the two loose boards centered. The two loose boards can be lifted off to reveal the compartments.

The most labor intensive part was the sides. lots of cutting and re-cutting with a jigsaw and beveling... using methods that I probably should not share. But in the end it came out great. I painted them black and screwed them in. It honestly looked better than I expected.

The view without the middle sections

And here it is all together with... a future project loaded in the back.

Leaf cargo deck. Day #1

A few months ago I purchase a Nissan Leaf. I do allot of driving and found that the payment on a Leaf was not much more than gas in my V6 car. Its fast, like my V6 car, cost nearly nothing to drive, and its better for the environment. I use mine for a delivery vehicle and found that it was really not very well suited as a delivery vehicle. The rear seats fold down but they are still a foot tall over the rear compartment. What i needed was that damn seat gone. And one day I finally did just that.

The seats

View from the rear hatch (back carpet taken out as well)

With the seats removed there was plenty of room for cargo but it still left me with an uneven floor that would be awkward to load gear in and out of. I then began design for a cargo deck that i could build to give me a nice flat floor to slide cargo in and out of. The first part of my design was to figure out what I wanted to fit under the deck since there would obviously be unused spaces underneath.

It turns out the road cases I use for my gear are the perfect height to fit within a 2x10 wood frame. Also it worked out well that using a 2x10 frame for the back would bring the main cargo deck height up to the same level as the rear sill. this also brought the deck up to the level of the rear shock towers so they would be less of an obstacle for loading cargo. The design for my cargo deck would now need to incorporate a hatch to access the compartment underneath.

 I trimmed a 2x6 to bolt up in front of my main 2x10 frame so i could have a good support across the full width of the car

With the bulk of the rear framework done it was time to move onto the front. where the front lip of the back seat attached was a raised portion that was conveniently dead strait and level. if the front portion was well attached to the rear it could rest there and cantilever the rest of the way to the back of the seats. to make sure I would have good structure i used two 4x4 beams lengthwise attached to a 2x4 across the width of them that would rest on the raised portion. For the very front part that would be against the back of the seat I cut a 2x4 that would run the full width to support the top. I also made the front portion match the width of the rear to keep everything uniform.

 Front portion of frame

And here it is. loosely attached to the rear portion and it worked out perfectly level across the top. its almost like the leaf was designed for this kind of modification. No trimming or shimming needed. I could move on to paint... Tomorrow